Please enable JavaScript to view this site.

MaxxECU online help

Navigation: » No topics above this level «

Manual Changelog

Scroll Prev Top Next More

2023-11-30

New chapters

CAN settings, new coding option setting.

Turbolamik controller.

Brake pressure, new analog input.

VW Passat 3C (R36) VAG PQ36 2008 (MED 9.1), new OEM CAN protocol.

Horn, new PDM input function.

Horn, new PDM output function.

Skidoo 900R 2024 (Bosch MG1C).

Honda TRX450R, new trigger added.

Mitsubishi 4G15T, new trigger added.

DSM 420A / Chrysler ECC, new trigger added.

Opel X16XE / XEL, new trigger added.

Jeep Cherokee 4.7 V8, new trigger added.

BMW N52 / N54 / S1000R, info added.

Pull-up resistor.

Dual coil, idle solenoid wiring examnple.

 

Chapter updates

Warnings, clarification when the warnings gets active.

CAN settings, new CAN ID offset setting added message rate settings.

MaxxECU Default CAN output, rotating ECU error codes added.

Mazda RX8, new coding option added.

Multi position switch, description added.

User frequency/duty.

AC magnetic clutch, max engine rpm added.

Fuel inj general, new fueling calculation mode added.

Fuel Adaptation, max IAT and MIN runtime settings added.

Electric waterpump control (PWM), new max PWM  duty setting added and note about CWA400.

Alternator control, max duty option added.

Electric waterpump control (on/off), info added.

Electric waterpump control (PWM), info added.

Jeep wrangler 2006 4.0L (36-2-2), info added.

LS3 CAM, new images.

Alfa Romeo Twin Spark 95 - 05 (CAM), information addded.

ECU Logging settings, more info added.

Use as digital input 3, note added.

Tach output, note added.

81 - Water/Methanol Injection, low level, new error code.

Water/Methanol Injection, low level sensor, new digital input.

Water/Methanol Injection, new output function.

Advanced warning outputs, new load condition.

Analog Inputs, merged page for all AIN inputs.

VVT error settings, new settings.

CAN Outputs, message rate option.

Virtual fuel tank Increase, new digital input.

Virtual fuel tank Decrease, new digital input.

Radiator FAN PWM, new output function.

DCT Control, new settings added.

DCT Settings, new setting added.

DSG 500 TCU Diagnostics.

Fuel Adaptation, added note about VE table 2.

Sensor setup, new wheel circumference setting for driveshaft sensor.

Speed/Gear, new setting between gears.

Power management, new activation mode setting + new time after launch start mode.

PDM Turn signal control, new setting.

BMW INPA diagnostic tool (GEN1), new INPA tool supplier added.

Speedometer output, value presentation added.

Ignition settings, angle range added.

Radiator FAN PWM, added max output duty.

Tachometer/speedometer, show monitor value x, renamed input.

Audi S3 1.8T 2003 VAG PQ34 (ME 7.5), more vehicles in the compatible list.

Turn signal left, Turn signal right, Turn signal hazard, added note about how to also enable the hazard output.

Speed/Gear, more options for speed source.

Built-in knock control, added how knock is detected.

Digital inputs, new example with AIN (0-5V) input.

 

2023-15-18

New chapters

GM LT1 Optispark, new information.

Alternating Trig/Home, new trigger.

CAN-AM Maverick X3 XRS Turbo RR 2020, new OEM CAN protocol.

CAN System user input 1 + CAN system user input 2, new analog input to output data on certain OEM CAN protocols.

DSG Shifter emulation, DSG shifter emulation.

PDM Wiper control, new page.

Wiper PWM Control, new page.

Resolution / scaling, new information.

Chevrolet Corvette C6 (E38 ECM), information added for REV3 plugin adapters.

 

Chapter updates

Extra fuel tables, add % to lambda table added.

VVT control intake/exhaust cam 1/2, PID frequency setting.

BMW DCT (GS7D36SG) gearbox control, changelog updated.

PDM High Beam, flash speed + flash count.

Buell XB9 DDFI2, new crank trigger.

Nissan CAS/GM LT1 cam with missing tooth crank, more information.

Shiftcut, add example image.

Lambda sensor, Haltech NTK CAN lambda added.

BMW E9x (MSS60), changelog update.

Audi A4 B7 VAG PL47 2006 (MED 9.1), value presentation support.

Audi RS6 C5 VAG PL45 (ME 7.1.1), value presentation support.

Audi S3 1.8T 2003 VAG PQ34 (ME 7.5), value presentation support.

Audi S3 8P VAG PQ35/36 2010 (MED 9.1), value presentation added + oil pressure warning light support.

Audi S4 B6 VAG PL46 (ME 7.1.1), value presentation added.

Tach output, updated the list of protocols activated to the value presentation function.

Software changelog, new version.

DCT/DSG Mode Switch, renamed input function.

Mazda RX8, engine oil pressure usage.

Staged injection, new setting.

Boost control: Closed loop (advanced), new activation setting.

Lambda sensor, new sensor shutdown setting.

PDM settings, new constant on mode setting.

Toyota 2NR, updated trigger images, Thanks Geoff :)

DSG hardware identifier, customer confirmed 02E 927 770 AE to be working.

Filters/error codes, MAP rate filter added.

Error codes, clear all codes, new input function.

Lambda control, new transient deactivation mode added.

KMS CAN Display, added transmitted CAN IDs.

OEM CAN Buttons, protocols added.

 

2023-01-25

Chapter updates

CAN Dash loggers (external) support, PowerTune Digital added.

Keypad setup, new default brightness setting and startup led information.

Fuel EGT correction, dynamic table as fuel EGT corrections.

Lambda control, reactivation table added.

DCT Mode Switch, renamed from Transmission DCT Mode Switch.

 

2023-01-10

Chapter updates

VAG DSG (DQ250), pinout update.

MaxxECU Default CAN output, DBC download link added.

FTDI USB, new service and repair chapter.

DCT shifter emulation, behavior of the reverse switch.

Transmission Reverse Switch, updated text of what is preventing the reverse to be commanded.

DSG hardware identifier.

Note added regarding having PDM20 on the same CAN bus as: Audi A4 B7 VAG PL47 2006 (MED 9.1), Audi RS6 C5 VAG PL45 (ME 7.1.1), Audi S3 1.8T 2003 VAG PQ34 (ME 7.5), Audi S3 8P VAG PQ35/36 2010 (MED 9.1), Audi S4 B6 VAG PL46 (ME 7.1.1).

BMW E9x (MSS60), changelog update.

Auto transmissions, added information on the ofgear external trans controller for the 722.6 gearbox.

DSG settings, new CAN emulation option.

Fuel usage, clarification on the fuel usage method.

Nitrous timer run, new input.

DSG hardware identifier, adjusted list.

Skidoo 900R 2022 (Bosch MG1C), new OEM CAN protocol.

Ignition acc correction, new function.

Ignition settings, new mode: Wankel wasted spark leading, sequential trailing.

Manual firmware update, new function to clear disabled tables to save memory.

MTune settings, new settings.

ECU lock, new password protected ultimate engine rpm limiter.

Lambda sensor, broken sensor lean error.

111 - Too many PWM channels, new error code.

112 - Lambda sensor malfunction. The signal is too lean, new ECU error code.

111 - Too many PWM channels, new ECU error code.

Oil Pressure Cut, cut behavior added, example added.

Line pressure, note about launch switch.

Shiftcut, new gear position sensor control mode.

BMW DCT error codes, GEN2 information added.

BMW DCT TCU firmware flashing, GEN2 information added.

BMW DCT CAN protocol, GEN2 information added.

DCT hardware identifier, GEN2 information added.

DCT installation and wiring, GEN2 information added.

MTune DCT Control, GEN2 information added.

MTune DCT Settings, GEn2 information added.

Keyboard shortcuts, A shortcut to toggle target arrow.

Filters/error codes, ODD-fire map filter.

Honda L15A / L13B, new trigger support.

Mercury Marine 2.5L 2-stroke V6, new crank trigger support.

Renault K4M (CAM), new CAM trigger.

Internal output system, latch output option added.

Jaguar AJ16 (CAM), new CAM trigger.

Rev limit, note about rev limit fuel enrichment removed.

Tachometer output, new enable method for rpm sweep with a short ondelay option added.

Speedometer output, new enable method for speed sweep with a short ondelay option added.

Ignition key, note added.

 

2022-08-05

Chapter updates

Lambda sensor, AEM X-series ch info added.

Toyota A340E/A341E, clarification how to get the desired gear.

BSD Protocol input, added pinout for the oil level sensor.

Information for the DSG protocol regarding CAN collisions in combination with MaxxECU default output protocol.

MDash Installation and setup, note added regarding language of tablet.

WBO module. revision changelog added.

Nissan 350Z (ECCS 2), rescaled tachometer output.

Tach output, added BMW E46 328i (MS42), BMW E46 330i (MS43) and Nissan 350Z (ECCS 2) to the supported value presentation list.

Lambda sensor, HV  electronics CAN lambda module added to the list.

Boost control: Open loop (simple), active above MAP setting.

Boost control: Closed loop (advanced), target boost reference clarification.

Ethanol sensor, custom calibration added.

Keyboard shortcuts, updated.

PDM Output settings, clarification on the PDM undercurrent.

VAG DSG, MaxxECU Default CAN output added note about CAN collisions between the default V1.3 CAN protocol and DSG.

Lambda sensor, pressure compensation.

Fuel start/warmup/ase, note about ASE max trim time changed.

Starter motor control, new setting to stop the engine.

BMW E9x (MSS60).

BMW DCT gearbox control, new options + changelog + blip is now always sent regardless of drivelogic mode, if there is a request.

Output config, Virtual output information and example.

Locking cells, new note.

VVT cam position inputs, new setting crank tooth offset.

Light low beam, auto off after 60 seconds added.

VAG DSG, changelog added.

Transmission, TCC/lockup PWM solenoid, new output added.

Lockup converter, ramping/pwm settings for TCC PWM solenoid.

 

New chapters

2JZ stepper.

Idle solenoids.

Oil Pressure Cut

Engine runtime+max reset. new digital input function.

Porsche Boxster 2003 with PSM (ME 7.8), new OEM CAN protocol.

Primary injector flow tracking has an invalid value, new tune warning.

BMW E85 EKPM (Fuel Pump Control module), new EKPM support.

Lights, flash to pass, new PDM digital input function.

Volvo C30 (ME9.0) BETA, new OEM CAN protocol.

Audi S4 B6 VAG PL46 (ME 7.1.1), new OEM CAN protocol.

Audi A4 B7 VAG PL47 2006 (MED 9.1), new OEM CAN protocol.

Lights, flash to pass, new PDM digital input.

Downshift cut, sequential gearbox control setting page.

Upshift control, sequential gearbox control setting page.

Upshift lockout, sequential gearbox control setting page.

Downshift control, sequential gearbox control setting page.

Nissan CAS/GM LT1 cam with missing tooth crank, new CAM trigger.

Volvo T6 NA CAM (B6294S2), new CAM trigger.

Honda J30A4, new crank and CAM trigger.

 

 

2022-03-04

Chapter updates

CAN Inputs, note about mask setting.

BSD Protocol input, waterpump connector pinout added.

BMW S65, more support.

MDash software changelog.

Tach output, added CAN protocol to the value presentation function.

BMW E9x (MSS60), EKPM controllable.

Transmission Mode Switch, typo...

Mazda RX8, fixed changelog.

Calibration, calibrate trigger inputs.

Triggers/Home inputs, new note about MAP dip value.

BSD Protocol input, note about available oil temperature from the oil level sender.

Fuel inj general, new injection methods.

Lambda sensor, new external CAN lambda added.

 

New chapters

BMW E9x EKPM (Fuel Pump Control Module).

CAN System EKPM control (0-100%), new analog input function.

Crankshaft Deceleration, new HOME sync for oddfire and 1-cylinder engines.

 

 

2022-02-15

Chapter updates

29 - MAP sensor error, clarification on error code.

Ford Focus RS/ST 2005 - 2012 (ME 9.0), AC request update.

Ethanol sensor, note about what is happening when a flex fuel sensor occurs.

BMW E9x DCT (GS7D36SG) gearbox control, Shifter emulation added, changelog update.

DCT installation and wiring, updated info for the DCT shifter emulation.

AIN (temperature), video added.

Ignition output cylinder x, screenshot + info change.

Ignition output, screenshot + info change.

DSG hardware identifier, DQ500 support.

VAG DSG control, DQ500 support.

Nissan CAS, V3 info.

Kawasaki JET SKI 1100 DI STX, image added.

MaxxECU Pinout, EGT pin information.

PDM settings, new setting to disable safety function.

PDM output functions, new note regarding safety function.

Transmission DOWN shift, more info.

Transmission UP shift, more info.

Transmission Neutral Switch, more info.

Transmission Reverse Switch, more info.

CAN Lambda Module Setup, corrected data.

Ignition settings, note on inverted setting.

BSD Protocol input, BSD waterpump information.

 

New chapters

DCT shifter emulation.

DCT drivelogic DOWN, new digital input.

DCT drivelogic UP, new digital input.

DCT Mode Switch, new digital input.

39 - Trigger error: No cam signal / incorrect pattern.

VAG DSG (DQ500), wiring information.

Fuel adaptation, enable adaptation, new digital input.

Fuel Adaptation, clarification and new settings added.

Fuel Pump Override, new digital input.

Mercedes-Benz S600 M120-980 6.0L, new trigger.

Mini Cooper SPI MK3 (36-1-1), new trigger.

Hyundai Kia G6DA, new trigger.

Jeep wrangler 2006 4.0L (36-2-2), new trigger.

Mercedes-Benz OM501 (36+1)

CANchecked MCE18, instructions how to setup.

Chassis SPORT mode, new digital input.

 

 

2021-11-09

Chapter updates

Audi S2/S4/S6 (5-cyl AAN), AC instructions updated.

Speed/Gear.

Sequential gearbox control.

Fuel Level sensor, wiring and setup.

OEM CAN Protocols, renaming of the Audi protocols.

Audi S3 1.8T 2003 VAG PQ34 (ME 7.5), protocol update.

Terminated engine harness Toyota 2JZ, REV3 harness information added.

BMW N54, BSD (alternator + oil level sensor) is now supported on this platform using our BSD board, see BSD Protocol input.

Nissan 350Z (ECCS 2), changelog update.

Throttle control, PID table mode information added.

Filters/error codes, lambda sensor overheating setting.

Triggers/Home inputs, unsyncronized start option.

Tune selector, stabilization time added.

92 - MaxxECU internal error: High internal temperature, when does this error code is triggered added.

Fuel EGT correction, clarification on how the EGT correction works.

VVT cam position inputs, allow missing gap overlap setting.

Lockup converter, Disable RPM clarification.

PDM settings, automatic fault reset clarification.

Staged injection.

Triggers/Home inputs, bipolar trigger setting information.

Idle stepper X (5/6 wire).

User Stepper Motor.

Filters/error codes, new short trigger/home pulse above rpm settings.

Advanced warning outputs, update to cover new digital input functions.

Sensor setup, new undriven wheel sensor setup option.

 

New chapters

Shift force.

CAN settings, new can wheel speed correction value.

CAN system power steering control, new analog input function.

Volvo Power steering, Volvo P1 servo control.

Audi RS6 C5 VAG PL45 (ME 7.1.1), new OEM CAN protocol.

Multi position switch

Ethanol sensor, input settings and hold value option with settings.

Advanced warning system, enable, new digital input.

EGT power cut, enable, new digital input.

Lean power cut, enable, new digital input.

Advanced Warning System, Enable Cut, new digital input.

Skidoo 900T 2019-2022 (Bosch ME17.8.5), new OEM CAN protocol.

Trigger, TRIGGER sensor

VVT exhaust/intake cam solenoid.

Warning light.

Warning system light level.

Ferrari-Maserati F136, new CAM trigger.

Rover 620, new crank trigger.

Yamaha V-max, new crank trigger.

Diahatsu 1KRVET, new CAM trigger.

Lotus Elise 910, new crank trigger.

GM LSJ, new crank trigger.

 

 

2021-06-29

Chapter updates

Extra fuel tables, VE blending with extra table support.

Fuel inj general, injector flow tracking with 4D axis.

 

 

2021-06-25

Chapter updates

Ignition settings, example settings.

DCT hardware identifier, gearbox support added to list.

Anti-lag, timeout RPM limit explanation.

Audi S2/S4/S6 (5-cyl AAN), added information about the auto gearbox is not supported.

Tach output, OEM CAN protocols added to the value presentation function.

Triggers/Home inputs, auto tracking information added.

Throttle control, sensor/target error delay.

Shiftcut, auto-zer and re-trigger settings.

Fuel Level 1/2.

Math channels, imperial units note.

Throttle control, PWM frequency information.

Traction control setup, new PID frequency setting.

 

New chapters

Join the MDash open beta program.

Settings shortcuts.

CAN Outputs, number of bytes in each message changed to 8.

CAN Inputs, mask operation information.

Advanced warning outputs, warning delay function.

Toyota GT86 OEM CAN protocol.

Aux injector, new output function.

BMW BSD bus 1 Input, new input function.

BMW BSD bus 1 Output, new output signal.

BSD Protocol input, BMW BSD protocol function.

Subaru/Toyota FA20, new trigger.

Subaru EZ30, new trigger.

 

 

2021-04-14

New chapters

Multi purpose sensors, pinout.

MTune 1.139 changelog.

 

 

2021-04-07

Chapter updates

Tune selector

Bluetooth settings, new tune selector options in MDash.

MDash software changelog, new features.

Anti-lag, new setting.

Filters/error codes, new filter triggering options.

User tables, new smoothing option.

Math channels, new smoothing option.

Nissan 350Z (ECCS 2), changelog changed.

OEM CAN Buttons, new OEM CAN protocols added.

 

New chapters

MDash Tune selector, new feature.

Overrun fuel cut disable, new digital input.

Wheel setup (use setup X when active), new input.

Audi S3 8P 2010 (MED 9.1), new OEM CAN protocol.

 

 

2021-03-22

Chapter updates

Relay - 85 and 86 was wrongly switched.

Throttle control, end position behavior.

Keyboard shortcuts, esc key, (SHIFT) HOME / END keys added.

Tach output, Tachometer value presentation.

Speedometer output, speedometer sweep function.

Fuel usage.

Fuel inj general, new fuel density correction table + adjusted injection method information.

User PID, D filter option.

Radiator FAN, Radiator Fan 2 output added and new dual mode.

Idle control target RPM.

Idle control settings.

Speed limit X enable/set.

Speed limiters.

EGT sensors, new note.

AIN (0-5V), samples times added.

Triggers/Home inputs, cam detection information.

BMW E9x (MSS60), ME 9.2 added to the list of working DMEs.

Honda CBR1000RR, trigger detection information.

RealTime Data, PRO analog output voltage explanation.

Ignition settings, min discharge time note added.

AC magnetic clutch, min engine RPM setting added.

Speedsensor transmission input shaft RPM, new note.

PWM module, CAN communication information added.

User PWM, period option.

Traction control setup, new note.

Starter motor input, new note.

GP RPM limiter, new settings.

Toyota 2JZ, WBO connector added to the list of available connectors.

E-pedals, updated pinout on the hella e-pedal wiring.

PDM Starter input control.

PDM Starter motor solenoid.

Shiftcut, gear counter feedback function, shift force triggers, reactivation timer.

AIN (0-5V) updated classes.

AIN (temperature) updated classes.

Triggers/Home inputs, missing tooth thresholds.

CAN Inputs, timeout settings, new mode.

CAN OBD-II input.

CAN Inputs, OBD2 input examples.

PDM Input settings, analog input calibration.

Switch decoder, PDM20 pullup note.

PDM settings, PDM CAN communication setting and example.

PDM Output 3-8 modes, better descriptions.

Keypad settings, Grayhill CAN keypad support.

PDM version, how to recover from a failed PDM firmware update.

Ford Focus RS/ST 2005 - 2012 (ME 9.0), changelog update.

Ford Mustang 2011 - 2014, OEM CAN buttons + tachometer value presentation.

 

New chapters

MTune 1.136 changelog

MAP/BARO Calibration.

Shiftcut enable, new digital input function.

Speed limit reset, new input.

CAN, disable all TX, new digital input to disable all CAN messages from MaxxECU when activated.

Neutral switch input.

Boost solenoid (closed loop) inverted

Boost solenoid (open loop) inverted

Cruise control, enable switch, new input.

Tachometer, show monitor value x, new input.

Polaris RMK800 2014-2015 (6-1), new trigger.

Mitsubitshi 6G75 (crank + CAM), new trigger.

Mitsubitshi 6G72, new trigger.

Subaru EJ25 (early 6 on crank 1 on cam), new trigger.

Tripmeter, reset, new input.

 

 

2020-09-29

Chapter updates

MaxxECU Default CAN output - New updated versions 1.3 default CAN protocol update.

AIN (0-5V) - New sensor class.

AIN (temperature) - New sensor classes.

 

New chapters

MTune 1.135 changelog

 

 

2020-09-25

Chapter updates

Nissan Patrol TB48 Y61 (ME C23) - Increased line pressure now possible.

 

New chapters

MTune 1.134 changelog

 

 

2020-09-08

Chapter updates

Idle stepper X (5/6 wire)

Digital inputs - New Input added (Auto transmission lockup enable).

Launch control - New PI gain values for the new RPM control drop mode.

CAN Lambda Module Setup - Added note about using a LSU 4.9 sensors instead of LSU 4.2.

CAN Lambda Module - Information on how to repin for LSU 4.9 usage.

PC installation - Disclaimer about not using a laptop car charger added.

AIN (temperature) - More settings.

AIN (0-5V) - More settings.

Math channels - Resolution added.

Tach output.

Extra ignition tables - New blending feature.

Extra fuel tables - New blending feature.

BMW M50 wiring - wrong "usage" link in 16-pin connector.

MaxxECU Pinout - Made it clearer with PRO CMC4 Sensor GND 3/ knock X wires.

MaxxECU PDM20 - Link to download able PDF added.

OEM CAN Protocols - All protocols with wheel speed inputs got a new note about always calibrate the wheel circumferences.

Lambda sensor - New sensor warmup option (delayed startup).

MaxxECU Pinout - MaxxECU MINI board soldering positions added.

Digital inputs wiring.

Analog inputs wiring.

 

New chapters

VAG DSG (DQ250) wiring information.

VAG DSG (DQ250) control.

VAG DSG CAN Protocol.

DSG settings.

DSG Control.

Auto transmission lockup enable - New digital input function.

DSG hardware identifier.

DSG RealTime Data description.

No direct digital input function.

Pull-up (with a coil).

Switch decoder - Wirings.

Switch decoder input.

Switch decoder - New function.

Output 3-8 modes - New PDM options.

 

 

2020-07-29

Chapter updates

Suzuki GSX-R

 

New chapters

Bit builder channels

 

 

2020-07-22

Chapter updates

GM LSx - MTune instructions for E-throttle/pedal removal added.

Fuel Adaptation - Notes added.

Knock control - Ignition trim table notes.

Tune problems - New tune problem added.

Overrun fuel cut - New Cut Ramp out time setting.

Launch control - New Speed source setting.

Rolling launch control - New add fuel setting added.

Pedal position - New allowed voltage error setting.

Keypad settings.

Lights, park - more inputs triggers this output.

User Cut tables - User description added.

Sensor setup - Input shaft RPM source.

BMW E9x DCT CAN protocol - Option to coexist with BMW E9x OEM CAN protocol.

OEM CAN Buttons - BMW E9x OEM buttons added.

 

New chapters

Memory almost full / fragmented - New tune problem added.

BMW E9x (MSS60) - New OEM CAN protocol.

Suzuki Jimny 2018 - New OEM CAN protocol.

Direct Output control from PDM - New PDM output function.

Turn signal light, constant flashing - New PDM output function.

Turn signal blinker.

Brake light settings.

Electric waterpump override input - New digital input.

Fan override input - New digital input.

FAN + Electric waterpump override input - New digital input.

Subaru 2-teeth cam/vvt trigger - New trigger.

 

 

2020-07-03

Chapter updates

DCT: No response from TCU.

DCT: No response from shifter.

Lambda table

CAN Analyzer - Outgoing data only added as an option.

DCT Settings - Blip delay + downshift option.

Ignition settings - new note about ignition lock angle.

Triggers/Home inputs - new Trigger angle options.

Audi S3 1.8T 2003 (ME 7.5) - Fuel consumption.

Mazda RX8 - ABS warning light error fix.

Speedometer output.

Internal output system.

User PID - Solenoid dead time settings.

Pedal to throttle table - New note.

Built-in knock control - Individual cylinder knock detection update.

Knock control - New retard step mode setting.

Engine FAN - New setting, disable fan when engine off.

DCT Settings - DCT, downshift with throttle blip.

Electric waterpump control (on/off) - Updated description.

Electric waterpump control (PWM) - Updated description.

Trigger systems - Trigger systems added.

VVT control intake/exhaust cam 1/2 - New setting "min rpm".

Keyboard shortcuts.

DCT Realtime Data description - New RealTime Data values added.

Error code 221 - Warning system channel 1, High/Low - Added the error code and channel relation.

DCT Settings - New settings added.

DCT Control - How to downshift and blip.

 

New chapters

MAP sensor as sync on ITB.

MAP sensor as sync on V-twin.

PDM version.

PDM settings.

PDM Output functions.

PDM Output settings.

PDM Input settings.

PDM internal outputs.

PDM input functions.

PDM output functions.

PDM Turn signal control.

Tune problems

Pulse function used on 2 inputs - Tune problem.

AIN class used on 2 inputs - Tune problem.

Output set on an unavailable output - Tune problem.

Output function used on more than 4 outputs - Tune problem.

No secondary injector outputs - Tune problem.

Ignition cylinder angle trim problem - Tune problem.

PDM Error Code 11-30 - PDM Output Overload/short circuit.

PDM Error Code 31-50 - PDM Output current to low.

PDM Error Code 91 - System shutdown from shutdown input.

Missing teeth (bipolar).

Ford Cosworth (4 on crank, 2 on cam) - New trigger.

Nissan QG18 - New trigger.

Subaru MY06 - MY14 (WRX STI) - New trigger.

Ford BARRA (CAM) - New trigger.

Nissan VQ30DE - New trigger.

DCT shifting options.

 

 

2020-04-23

Chapter updates

MaxxECU Default CAN output

Accelerometer - free rotation mode.

Power hold relay.

 

New chapters

KMS CAN Display

 

 

2020-04-21

Chapter updates

PWM module.

Modules.

E-Throttle bodies - GM SENT body added.

BMW DCT - Wiring information.

BMW DCT error codes.

14 - E-Throttle overtemperature/short circuit.

E-Throttle bodies - Ford Barra update.

OEM CAN Buttons - Corvette C6 update.

Corvette C6 (GM E38 ECM) - Cruise  control.

E-pedals - Changed notes.

Mazda RX8.

Trigger logger.

Trigger oscilloscope - Trigger source as Cylinder TDC.

Keypad setup - Write new CAN protocol.

Launch control - Launch boost duty, new note.

MDash Software changelog.

Mazda RX8 - Odometer update.

VVT control intake/exhaust cam 1/2 - Feed forward update.

 

New chapters

SENT protocol input - new digital input.

Haldex GEN1 wiring.

VW Haldex GEN1 - Control option and example.

BMW DCT TCU firmware flashing

BMW INPA diagnostic tool.

DCT hardware identifier.

DCT clutch relearn.

BMW DCT gearbox control - DCT big HOWTO.

DCT clutchkick/burnout mode - Digital input for the DCT control.

CAN Analyzer.

CAN Test Output.

Lambda module relay - New output function for snow mobiles with shot starter and the usage of our CAN WBO module.

User Cut Table X, enable - Digital input function.

Throttle blip enable - New digital input.

User Cut tables - New engine cut function.

189 - SENT protocol Error - New error code.

Throttle blip.

DCT: No response from TCU - New ECU error code.

DCT: No response from shifter - New ECU error code.

 

 

2020-03-11

Chapter updates

Live-logger - New note.

MDash Software changelog

 

 

2020-02-27

Chapter updates

Audi S3 1.8T 2003 (ME 7.5) - Engine oil pressure added (using User CAN INPUT), base tune updated in downloads.

MDash Software changelog

 

 

2020-02-25

Chapter updates

79 - EGT-sensor: Sensor short-circuit to ground

MDash Software changelog

 

 

2020-02-11

Chapter updates

Fuel inj general  - Fuel flow.

BMW E46 330i (MS43) - Only MS43 info here now.

Filters/error codes - MAP filter update.

ECU Logging settings - Limit logging speed on certain values.

Auto transmission, switch to 2nd shift table - Digital input function.

Auto transmission gear selector - Digital input function.

Auto transmission manual mode switch - Digital input function.

Auto transmission, enable WOT RPM shift - Digital input function.

Built-in knock control.

Knock sensors.

Knock control.

Knock sensing.

Ethanol sensor.

Nitrous General - NFR.

Filters/error codes - MAP filter examples.

Distributor - Better explanation.

Renix 44-2-2 - no CAM input example configuration.

Renix 66-2-2-2 - no CAM input example configuration.

BMW M62 - CAM trigger information.

Ford ST170 (CAM) - CAM trigger information.

Wankel - Basic wankel setup information.

MDash Boost selector switch - New instructions.

MDash Input switch - More examples.

 

New chapters

Power management - New video for power adder.

Toyota A340E/A341E - Auto gearbox information.

Toyota A650E - Auto gearbox information.

Transmission control - General settings.

Transmission control - Shift points.

Transmission control - Shift points, switched.

Transmission control - Shift points, RPM based.

Transmission control - Line pressure.

Transmission control - Lockup converter.

BMW E39 M5 (MSS52)  - NEW OEM CAN protocol.

BMW E46 328i (MS42) - NEW OEM CAN protocol.

Starter motor input function.

Starter motor control output function.

211 - DCT: clutch slip engine cut - New ECU error code.

212 - DCT: Upshifting took to long to complete - New ECU error code.

213 - DCT: Downshifting took to long to complete - New ECU error code.

181-188 - Wideband lambda module X error

221 - Warning system channel 1, High/Low.

Digital inputs - Latch support.

BMW S65 - Engine support and wiring information.

Digital inputs - How to make DIN 3 visible.

Use as digital input 3 - New video tutorial.

 

 

2019-12-19

Chapter updates

Digital inputs - More examples.

Sensors (CLT,IAT,TPS) - How to setup EGT input as a IAT sensor.

EGT sensors - How to setup EGT input as a IAT sensor.

USB troubleshooting.

21 - Configuration error: Incorrect fuel/ignition-mode

22 - Configuration error: Wrong cylinder count with current fuel/ignition-mode

Boost solenoids - wiring and information.

Installation and setup - Android stereo note.

 

New chapters

External EGT - wiring information.

Acceleration module - wiring information.

 

 

2019-10-30

Chapter updates

Power management - New time after launch start mode.

Anti-lag - New fuel drop table + new ignition control mode.

Fuel acc enrich - New settings.

Launch control - New settings.

CAN OBD-II input - RPM and TORQUE from vehicle bus.

AIN (0-5V) - Accelerometer analog inputs added.

Lambda sensor - MaxxECU CAN WBO.

OEM CAN Buttons - Porsche 996 CAN support.

Porsche 996 2001 (ME 7.8) - Cruise buttons.

BMW E90/E92 (DCT).

Trigger oscilloscope.

Lambda sensor.

MDash Software changelog - 1.47 update.

 

New chapters

Accelerometer.

Nitrous purge solenoid - New output.

Nitrous purge - New input.

Temporary cylinder shutoff - Function to disable injectors/ignition outputs to test for missing cylinders while engine is running.

CAN Lambda Module Setup.

DCT Settings.

DCT Control.

DCT hardware upgrade.

New trigger: Volvo B5244S (CAM + VVT).

 

 

 

2019-09-23

Chapter updates

Introduction - MDash update changelog + movie.

 

 

2019-09-17

Chapter updates

42 - Protection: Lean power cut

41 - Protection: Boost limit activated

Fuel start/warmup/ase - ASE is zeroed out in MTune 1.122 after 120seconds.

Table Smoothing - New images and a video demonstration.

BMW E46 330i (MS 42/43) - Engine oil pressure warning light.

Porsche 996 2001 (ME 7.8) - Oil level check.

MDash Android app - 1.40 update.

 

New chapters

OEM CAN Buttons

MDash Boost gauge

CAN Lambda Module - Wiring information.

 

 

2019-09-04

Chapter updates

Lambda sensor, information regarding Motec CAN WBO controller.

Nissan CAS, added NZ wiring CAM trigger kit settings.

Keyboard shortcuts.

ECU Logging settings.

MDash Input switch.

Bluetooth settings.

Lambda sensor.

BMW M54 (MS42/MS43).

Shiftcut.

Boost control: Closed loop (wastegate back pressure control).

Trigger, HOME+CAM dual sensor, cam sensor - renamed input.

Launch control.

Triggers/Home inputs.

Filters/error codes - Battery voltage filter + Over voltage engine cut.

BMW E90/E92 (DCT) - CAN protocol information update.

Fuel inj general

Sensors (CLT,IAT,TPS) - Custom fail-safe thresholds for IAT and CLT sensor.

Wheel setup - Tire growth correction for speed calculations.

AIN (0-5V) - Custom fail-safe thresholds and CEL code activation.

Digital inputs - More digital inputs added.

Error codes - new codes.

Trigger oscilloscope.

Trigger logger.

MDash introduction - MINI/STREET cannot communicate with MDash over USB...

Ignition settings - Dual distributor text updated.

Ignition output.

Injector outputs (INJ).

Log viewer.

Filters/error codes

Mazda MX5 NB (99-05) - optional update.

Dodge Viper CAM trigger.

12 - CLT sensor error

ECU Logging settings

 

New chapters

New PWM Input Frequency+Duty digital input function to read frequency and duty.

New digital input Boost Control Enable.

BMW S14 (crank+cam) trigger system.

Suzuki G16B (ON CAM).

BMW DCT - Wiring.

MTune DCT Settings.

MTune DCT Control .

121 - AIN error - New error code.

97 - Hard fault/Memory protection - New error code.

48 - Overvoltage protection cut - New error code.

38 - Trigger/CAM pattern expected error - New error code.

Engine Oil Temperature.

Engine Oil Pressure.

Math channels (combine tables and values to new values).

Ignition output cylinder x.

MTune File formats.

Mazda2 ZY-1500cc ZJ-1300cc Z6-1600cc. - New trigger.

Suzuki Swift M15A 2005 - 2010.

Diahatsu Mira JB (4+1 on CAM).

MTune table Smoothing.

 

 

2019-04-29

Chapter updates

E-Throttle bodies (new pinouts).

 

New chapters

Lotus Elise/Exige 2007/2009 OEM CAN protocol (for 1.122 release)

 

 

2019-04-03

Chapter updates

MaxxECU Pinout (MINI CAN note).

Audi S3 1.8T 2003 (ME 7.5) (changelog update).

Staged injection (video added).

CAN Inputs (more examples and features).

Lambda sensor (info added).

Speed/Gear (info added).

GM LSx terminated engine harness update.

95 - Table CRC error (error code update)

Launch control (new cut mode).

Nitrous Stage (solenoid test feature).

Trigger CAM/HOME (MINI update).

Bluetooth settings (new function).

 

New chapters

Angle logger

CAN OBD-II input

Single pulse per 720 degrees (piggyback trigger)

Gear position sensor

User Stepper Motor

 

 

2019-02-27

Chapter updates

BMW E46 330i (MS 42/43) documentation.

 

New chapters

MTune 1.120 release information

User PID enable control digital input.

User PID control function.

 

 

2019-02-14

Chapter updates

Ford Mustang 2011 - 2014

Honda K20A2

Ignition lock/idle control

Speed/Gear

 

New chapters

PDM

PDM General settings

PDM Output settings

PDM Input settings

PDM internal outputs

Honda CBR1000RR trigger

Renix 44-2-2 trigger

Suzuki Swift K12B trigger

Harley-Davidson EVO trigger

Yamaha jet ski waverunner (2010) trigger

CAN Keypads wirings

MaxxECU PDM20

CAN Keypad setup

CAN Keypad settings

 

 

2019-01-23

Chapter updates

BMW M54 (MS42/MS43)

Plugin ECU solutions

MaxxECU Pinout

 

 

2018-12-11

New chapters

Honda K20A2

GM LT5 gen I (8+1 on crank)

 

Chapter updates

MTune PC installation

Ford Focus RS/ST 2005 - 2012 (ME 9.0) OEM CAN Protocol

Ford Focus RS/ST 2010 (ME 9.0) Plugin.

Plugin ECU solutions

Trigger systems

 

 

2018-11-08

New chapters

Cruise control

Autotune (from logfile)

Autotune (local)

MAP-sensor error code

Fuel/ign cut and ignition retard reasons.

Jeep Cherokee (MJ-XJ 19) trigger.

Renix 66-2-2-2 trigger.

lock cells

BMW E46 MS43 CAN.

Nissan Patrol Y61 CAN.

CAN System Fuel Consumption Meter.

CAN System Torque Value.

Rate of change

GM LSx terminated engine harness

BMW M54 (MS42/MS43) Plugin

Alternator control output

MDash installation and setup

MDash on screen warnings

MDash shiftlight

MDash diagnostics (error codes)

MDash software changelog

MDash usage

 

Chapter updates

Power management system

Fuel pump priming time, used by the fuel pump relay output.

Radiator fan output

Idle control settings.

VVT duty % compensation

Locked idle ignition

Hide infrequent trigger errors.

Advanced warning system.

ECU power hold

Rev limit.

GP RPM limit tables

Engine counters

Dialog to add/remove cells

Keyboard shortcut

MTune settings

ECU lock

Common operations

PC installation

True 4D

3D surface tuning operations

2D table tuning operations

USB troubleshooting

Porsche 996 2001 (ME 7.8)

Ignition lock/idle control

Idle control settings

Porsche 996 turbo 2001 - 2005

Launch control

Idle control settings

MDash introduction

Error codes